We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Neewer 60 LED Dive Light: Specs, Setup and Buying Tips for Divers

Learn how to choose, set up and use a Neewer 60 LED dive light, with beam, battery and mounting tips for safer night and low-visibility dives.

Updated November 2026

The Neewer 60 LED dive light is a compact underwater light that many divers consider for night dives, wreck penetration and general low-visibility work. This guide explains what to check before you buy, how to prepare the light for a dive, and how to avoid the mistakes that cause lights to fail at depth. By the end, you should know whether this model fits your diving and how to use it confidently.

Check What Matters Before You Buy

Start with the job you need the light to do. A primary light for a night dive needs a wide, even beam to show your buddy and the reef, while a backup light only needs to get you safely to the surface. Confirm the rated depth on the packaging and compare it with the deepest dives you plan to make. Look for an O-ring seal design and a battery type you can easily replace or recharge while traveling.

Set Up and Prepare the Light

Preparation is where most dive light problems begin, so treat it as a checklist rather than an afterthought.

  1. Charge the battery fully the night before, and confirm the charger indicator shows completion.
  2. Remove the O-ring, clean it, and check it for hair, grit, or nicks. Apply a thin layer of silicone grease sparingly.
  3. Seat the O-ring back in its groove with your fingers, not a tool, so it cannot be pinched.
  4. Tighten the head or cap by hand until it stops. Overtightening can damage the threads.
  5. Turn the light on out of the water to confirm it works, then turn it off before you enter.

Use the Beam Effectively Underwater

Learn the modes before the dive, because you will not want to hunt for the switch at depth. Most users run the light on a moderate setting for general navigation and save the brightest output for signaling or photography. Aim the beam slightly below your buddy’s line of sight to avoid blinding them, and keep it steady rather than sweeping it across the water. Mount a backup light on a separate attachment point so a single failure does not leave you in the dark.

Mounting and Handling

Use a wrist or hand-held lanyard for the primary light so you can control direction without letting go. Keep the light clipped to your BCD or a D-ring when you need both hands for valves, slates or equipment. Avoid resting the light on the reef, since contact can damage coral and stir up silt.

After the Dive: Rinse and Store

Rinse the light in fresh water, including the seams and the area around the switch. Dry it fully before opening the battery compartment or cap. Store the light with the battery at a partial charge if you will not use it for several weeks, and check the O-ring each time you remove the cap.

Common Mistakes

  • Skipping the O-ring inspection, which is the most common cause of flooding.
  • Using too much grease, which can attract grit and make the seal slide.
  • Running the brightest mode continuously, which drains the battery faster than expected.
  • Shining the beam directly into your buddy’s mask during the dive.
  • Leaving the light uncharged between trips.
  • Silicone grease for O-rings: keeps the seal supple and reduces the chance of leaks. View on Amazon
  • Wrist lanyard for dive lights: keeps the light secured to your hand so you can adjust direction easily. View on Amazon
  • Backup dive light: provides a second light source in case the primary fails. View on Amazon

For more background on choosing lights, see 6 Best Dive Light LED Picks Compared for Night and Deep Diving (2026) and Wrist Mounted Dive Light: 7 Tips for Choosing and Using One Safely.

FAQ

Is the Neewer 60 LED dive light suitable for night diving?

It can be, provided you confirm its rated depth and beam output match your planned dive profile. Many divers still carry a separate backup light for night dives.

How often should I replace the O-ring?

Inspect it before every dive and replace it when you see cracks, flattening, or persistent debris damage. Manufacturers generally recommend periodic replacement, so check the instructions that came with your light.

Can I use the light in saltwater without rinsing it?

No. Rinse the light in fresh water after every saltwater dive to prevent corrosion and seal wear.

Conclusion

A reliable dive light depends on careful preparation, a clean and well-seated O-ring, and a clear plan for how you will use the beam underwater. Check the rated depth, run through the setup checklist before each dive, and rinse and dry the light afterward. If you have questions about your specific diving conditions, consult a dive professional or a certified instructor.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our scuba gear for women guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Scuba Women.