Light Monkey LED Dive Light: Setup, Use and Buying Tips for Divers
Learn how the light monkey led dive light works, how to set it up, and what to check before buying, so you get a reliable beam on every dive.
Updated November 2026
A light monkey led dive light is a compact, budget-minded underwater light that lets you see color, spot marine life and check your gauges in low-light conditions. In this guide you will learn how to pick the right model, prepare it before a dive, and use it safely. You will also learn what to check after each dive so the light stays dependable.
Choose the Right Light Monkey Model for Your Diving
Start by matching the light to the way you dive. A light used for a shallow night reef check has different needs than one used for a deeper wreck penetration. Look at three things before you buy:
Shopping for one? See our guide: 6 Best Dive Light LED Picks Compared for Night and Deep Diving (2026). For another angle, check out Micro Kickboard Maxi Kick Scooter With LED Lights: Buying and Setup Guide (2026).
- Dive depth and environment: Shallow, clear water needs less output than murky inland or deep water.
- Run time: Check the manufacturer’s stated run time at the brightness level you expect to use most.
- Mounting style: Decide whether you want a handheld light, a wrist mount or a clip to your BCD.
If you are new to night diving, a moderate output with a long run time is usually more practical than the brightest option available. For more on how beam shape affects what you see, read Wide or Narrow Beam Dive Light: Which Should You Choose?.
Set Up the Light Before Every Dive
Most failures happen before the dive, not in the water. A short pre-dive routine catches most problems early.
- Charge the battery fully using the charger supplied with the light. Do not use a charger from a different product.
- Inspect the O-ring and sealing surfaces for hair, grit or nicks. Clean them with fresh water and dry them thoroughly.
- Apply a thin, even coat of silicone grease to the O-ring. Too much grease can attract debris, so use just enough to give a slight sheen.
- Close the housing firmly and confirm the lock or cap is fully seated.
- Turn the light on in a bucket or sink before the dive to confirm it lights at your chosen setting.
If your model uses a different battery or charging method, check the manufacturer’s manual. The steps for charging a similar model are covered in Sola Dive Light Charging: A Step-by-Step Guide for Divers.
Use the Light Safely Underwater
Good light technique improves both visibility and safety. Hold the light slightly to the side of your body rather than straight ahead, which reduces backscatter from particles in the water. Keep the beam at a moderate angle to the bottom so you see texture and color rather than a glare.
Use the lowest brightness that gives you what you need. This saves battery life and reduces disturbance to nocturnal animals. Keep the light on a lanyard or wrist strap so you do not drop it when you need both hands for a task.
Always carry a backup light for night dives. Your primary light should never be your only source of illumination. Plan your dive so that you can ascend safely if the light fails. Consult a dive professional or your certifying agency for guidance on night diving procedures.
Check and Maintain the Light After Each Dive
Rinse the housing in fresh water as soon as you can after diving, and soak it briefly if it was exposed to salt. Open the housing in a dry place, inspect the O-ring again and store the light with the battery at a partial charge if the manufacturer recommends it. Replace any O-ring that looks flattened, cracked or cut. Keeping a spare O-ring in your dive kit is a simple habit that prevents a lot of lost dives.
Recommended gear
- Silicone O-ring grease: Keeps the seal supple and reduces the risk of leaks. View on Amazon
- Spare O-rings for dive lights: A cheap backup that can save a night dive if one fails. View on Amazon
- Wrist lanyard for dive lights: Keeps the light secured while your hands are busy. View on Amazon
Tips and Common Mistakes
- Do not skip the bucket test before a dive. A light that works on the dock may not work after a rushed reassembly.
- Avoid over-tightening the housing. Excess force can damage the O-ring and the threads.
- Do not store the light fully discharged for long periods, as this can shorten battery life.
- Keep a log of run times so you know when the battery is getting weak.
- Rinse the light after every dive, even if you only dove in fresh water.
FAQ
Is a light monkey LED dive light suitable for beginners?
Yes, a moderate-output model with a clear mounting option is a practical choice for new divers. Pair it with a backup light for any night dive.
How often should I replace the O-ring?
Replace it whenever it looks flattened, cracked, cut or stretched. Many divers also replace it on a regular schedule, since a small failure can cause a flooded housing.
Can I use the light in fresh water as well as salt water?
Yes, but rinse it in fresh water after salt water dives. Salt residue can corrode contacts and degrade seals over time.
Conclusion
A light monkey led dive light works best when you choose the right model, run a short setup routine before each dive and maintain the housing afterward. Start with the bucket test and a clean O-ring, and use the lowest brightness that gives you a clear view. With those habits in place, your light will be ready when you need it most.
Related reading
- Tovatec Fusion Video LED Dive Light: 6 Best Picks for Underwater Video (2026)
- Princeton Tec Shockwave LED Dive Light: 5 Best Picks for Night Diving (2026)
- Princeton Tec LED Dive Light Review: Strengths and Limitations
- Neewer 60 LED Dive Light: Specs, Setup and Buying Tips for Divers
Ready to choose one?
