We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Dive Rite CX2 Light: Setup, Use and Buying Tips for Divers

Learn how to choose, mount, charge and use a Dive Rite CX2 light safely, with practical tips for night dives and backup planning.

Updated November 2026

A Dive Rite CX2 light is a compact canister-style dive light built for divers who want reliable illumination without a bulky setup. This guide covers what the dive rite cx2 light is designed for, how to set it up correctly, and how to use it safely on night dives and as a backup. By the end, you should know what to check before every dive and how to avoid the most common handling errors.

What the CX2 Is Designed For

The CX2 belongs to Dive Rite’s canister light family, which places the battery pack in a sealed housing that is typically clipped to a harness or BCD. Canister designs are favored by divers who want long run times and a steady beam, though they add some bulk compared to handheld lights. Before buying or using one, confirm the exact model variant you have, because battery types, mounting hardware and lamp heads can differ between versions. Manufacturer documentation is the authoritative source for those details.

Setup and Pre-Dive Checks

Setup is where most avoidable problems start. Work through these steps before every dive:

  1. Inspect the O-ring and sealing surfaces for hair, grit, nicks or dried lubricant, then clean and re-lubricate with a silicone-based grease the manufacturer recommends.
  2. Confirm the battery is fully charged and seated correctly, and that the battery compartment is closed to the specified torque.
  3. Test the light on the surface in a dark area to confirm the beam is on and the switch operates smoothly.
  4. Check the mounting bracket or clip and make sure the canister cannot slide or rotate during the dive.
  5. Secure the lanyard or safety tether so the light cannot be lost if it is dropped.

Mounting Position

Mount the canister where it does not press into your ribs or interfere with your inflator, gauges or computer. A position just off-center on the chest or at the hip works for most divers. Test your range of motion, including reaching for your octopus and checking your buddy, before you enter the water.

Using the Light Safely

Keep the beam pointed where you are looking, not into your buddy’s mask. Use the lowest brightness that gives you the visibility you need, since higher output drains the battery faster and can cause backscatter in particulate-heavy water. On night dives, establish a light signal protocol with your buddy before descending, and agree on what the signals mean for “check on me” and “I need to surface.”

Managing Battery Life

Track your run time from the start of the dive. Many divers carry a second light or a backup as a matter of routine, and plan dive duration with a margin of safety well inside the rated run time. Avoid storing the light fully discharged, and recharge after each use so the battery is ready for the next dive.

Post-Dive Care

Rinse the light in fresh water and dry the outside before opening the housing. Do not open the canister on a wet deck or with water on the seal. Inspect the O-ring after every few dives, and replace it on the schedule the manufacturer specifies or sooner if it shows wear.

  • Silicone O-ring lubricant keeps the seals supple and reduces the risk of leaks. View on Amazon
  • Backup dive light gives you a second source of illumination in case the primary light fails. View on Amazon
  • Light lanyard or tether prevents loss if the light is dropped or knocked free. View on Amazon

Common Mistakes

  • Skipping the O-ring inspection because the light worked on the last dive.
  • Mounting the canister so it rotates or digs into your side during movement.
  • Running the light at maximum output for the entire dive.
  • Storing the battery discharged for long periods.
  • Diving at night with only one light and no agreed signal plan with your buddy.

For related setup and buying guidance, see Dive Rite Canister Light: How to Choose and Use One (Step-by-Step) and Wide or Narrow Beam Dive Light: Which Should You Choose?. If you use the light for technical or deep diving, 6 Best Dive Rite Backup Lights for Safe Night and Technical Dives covers backup options.

FAQ

How often should I replace the O-ring on a Dive Rite CX2 light?

Follow the replacement interval in the manufacturer’s documentation, and replace it sooner if you see cracks, flattening or nicks. Inspect it before every dive because a single compromised seal can flood the housing.

Can I use the CX2 as my only light on a night dive?

Most training agencies and experienced divers recommend carrying a primary light plus at least one backup. Relying on a single light leaves you without illumination if it fails.

What should I do if the light floods?

Turn the light off if it is safe to do so, end the dive according to your plan, and do not reopen the housing until it has been thoroughly dried. Consult a qualified dive professional or the manufacturer before using it again.

Conclusion

A dive rite cx2 light performs well when it is set up carefully, mounted securely and checked before every dive. Build a short pre-dive routine, manage battery use, and carry a backup. Consult a qualified instructor or the manufacturer’s documentation for model-specific procedures.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our scuba gear for women guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Scuba Women.