We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Anchor Dive Light 189: Setup, Beam Use and Buying Tips for Divers

Learn how the anchor dive light 189 works, how to set it up, and what to check before a dive. A practical guide to choosing and using it well.

Updated November 2026

The anchor dive light 189 is a compact underwater light designed to help divers see color, detail and their dive buddy at depth. This guide explains what to check before you buy one, how to set it up for a safe dive, and how to use its beam so you get the most from it. If you are new to dive lights, start with the basics and then work through the setup steps below.

Understand What the Anchor Dive Light 189 Is Built For

Most dive lights fall into two broad groups: primary lights you rely on for navigation and signaling, and backup or video lights used for color correction and photography. The anchor dive light 189 is best thought of as a lighting tool for recreational and night diving, where the goal is to see clearly rather than to illuminate a large area. Before you use it, check the manufacturer’s listed depth rating and run time so you know the limits you are working within.

Shopping for one? See our guide: 5 Best Scuba Dive Light Picks: Top Options Compared (2026). For a deeper look, Anchor Light for Boat: Rules, Types and How to Install One covers this in detail.

Set Up the Light Before Every Dive

A light that fails at depth is a problem you cannot solve on the bottom, so setup matters more than any single feature. Work through these steps the night before and again at the dive site.

  1. Charge the battery fully and confirm the charger indicator shows a complete charge.
  2. Inspect the O-ring and the lens for hairline cracks, sand, lint or old grease.
  3. Lightly lubricate the O-ring with silicone grease, then wipe off any excess.
  4. Seal the housing, press the power switch briefly, and confirm the light turns on at each output level.
  5. Mount the light on your wrist or BCD so you can reach it without searching.

Use the Beam Correctly Underwater

Beam handling determines how much you actually see. Hold the light slightly to one side of your body rather than straight in front, so the backscatter from particles in the water does not fill your field of view. Use the lowest brightness level that shows what you need. Higher output drains the battery faster and creates more glare in turbid water, so save full power for emergencies or for checking a specific feature.

Check the Light After Each Dive

Rinse the housing in fresh water, dry the exterior, and open it only in a dry place. Check the O-ring for nicks and reapply grease if it looks dry. Store the battery at a moderate charge if you will not dive for several weeks, following the manufacturer’s storage guidance. Regular checks catch small problems before they cause a flooded housing.

Common Mistakes

  • Skipping the O-ring inspection because the light worked on the last dive.
  • Running the light at maximum output for the whole dive, which shortens run time.
  • Storing the light fully discharged for long periods.
  • Pointing the beam straight ahead in murky water, which creates glare.
  • Rinsing the housing with salt water left on the seal.
  • Silicone O-ring grease helps keep the housing seal supple and reduces the chance of a leak. View on Amazon
  • A soft-bristled brush and fresh water rinse kit makes it easier to clean the lens and seal after salt-water dives. View on Amazon

FAQ

How do I know if the anchor dive light 189 is suitable for my dives?

Compare the manufacturer’s depth rating and run time against your planned dive profile. If you regularly dive deeper or longer than those specs, choose a light with a higher rating.

How often should I replace the O-ring?

Replace it when you see cracks, flattening, or persistent dryness, even if it still seals. Many divers also swap it on a regular schedule, which is a sensible habit.

Can I use the light as my only light source for night diving?

Most divers carry a backup light in addition to a primary light for safety. Check your certification agency’s guidance and your local dive operator’s requirements before relying on a single light.

Conclusion

Setting up the anchor dive light 189 correctly, using the beam sparingly, and inspecting it after every dive will keep it reliable. Small habits like checking the O-ring and managing output make a noticeable difference at depth. For health and safety questions about diving, consult a certified dive professional.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our scuba gear for women guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Scuba Women.