We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Dive Rite CX3 Light: How to Choose, Mount and Use It Safely

Learn how to choose, mount and use a Dive Rite CX3 light for safer night and cave dives, with setup steps, common mistakes and a quick FAQ.

Updated November 2026

The Dive Rite CX3 light is a compact canister-style dive light built for divers who want reliable, focused illumination without a bulky setup. This guide explains what the CX3 is suited for, how to set it up correctly, and how to use it with good habits that keep you safe on night and low-visibility dives. Read it before your next trip so you know what to check on the surface, not on the bottom.

Know What the CX3 Is Designed For

The CX3 is a canister light, meaning the battery and LED sit in a sealed housing that you mount to a handle, lanyard or primary light arm. It suits recreational night dives, wreck penetrations within the limits of your training, and backup duty on technical dives where a second light is required. Before you buy or use one, check the manufacturer’s stated depth rating, burn time and beam specifications for your exact model, because these vary between versions.

Set Up the Light Before You Get Wet

Most of the problems divers have with canister lights happen at home, not underwater. A few minutes of checking on land prevents a dark dive.

  1. Confirm the battery is fully charged and that the charger matches the battery type. Lithium chemistries need the correct charge profile.
  2. Inspect the O-ring for nicks, hair, sand or old grease. Clean it with a lint-free cloth and apply a thin, even layer of silicone grease.
  3. Check that the lens is clean and free of scratches that could scatter light into your mask.
  4. Seat the canister and tighten the closure just until it is snug. Overtightening can damage the O-ring and make later removal difficult.
  5. Turn the light on at the surface and test each brightness mode. Note which mode you will use for navigation and which for signaling.
  6. Attach the light to your mounting point and confirm it cannot snag on reels, hoses or your gauges.

Mount and Position the Light for Better Visibility

Where you hold or clip the light changes how much usable light reaches your eyes. Position it so the beam sits slightly below your line of sight and angled forward, which lights up the floor and your immediate path without causing backscatter from particles directly in front of your mask.

Keep Your Hands Free

Clip the light so you can operate your reel, inflator and gauges without fumbling. Divers who hold the light in a hand tend to drop it or point it into their own faces. A secure mount on a primary arm or a bungee-style lanyard works better for most recreational dives. A related read: 6 Best Dive Lights with Laser Options for Night and Reef Diving.

Use the Light Safely During the Dive

Good technique matters as much as the hardware. Keep your beam moving in a smooth arc rather than sweeping it across your buddy’s face. Stay within arm’s reach of your buddy so both lights overlap and each of you can see the other clearly. If the light flickers or dims, switch to your backup light immediately rather than waiting until the primary fails completely.

Plan for light failure before you descend. Agree on a hand signal with your buddy for “light out” and know the ascent or exit route from memory. For guidance on backup lights and redundancy planning, see 6 Best Dive Rite Backup Lights for Safe Night and Technical Dives, and for a broader view of mounting options, see Wrist Mounted Dive Light: 7 Tips for Choosing and Using One Safely.

Maintain the CX3 After Every Dive

Rinse the light in fresh water and dry the exterior before opening the canister. Remove the battery if the manufacturer recommends it for storage. Inspect the O-ring after each dive, replace it when it shows cracks or flattening, and store the light with the canister slightly open or the O-ring removed if your model’s instructions advise this. Charge the battery regularly rather than letting it sit fully discharged for weeks.

For a fuller walkthrough of charging and setup routines, the site’s guide on Dive Rite Canister Light: How to Choose and Use One (Step-by-Step) covers the general process for canister-style lights.

Common Mistakes to Avoid

  • Skipping the O-ring check, which is the most common cause of water leaks.
  • Overtightening the closure and damaging the seal.
  • Pointing the beam straight ahead, which lights up particles and reduces visibility.
  • Using a battery or charger not matched to the light’s specifications.
  • Diving without a tested backup light on any dive where darkness is a risk.

A spare O-ring kit in the correct size for your canister lets you fix a seal problem before the dive instead of abandoning it. View on Amazon

Silicone grease formulated for dive equipment keeps O-rings supple and helps the canister close smoothly. View on Amazon

A dedicated lanyard or bungee mount keeps the light secured to your harness, so you are not gripping it for the whole dive. View on Amazon

FAQ

Is the Dive Rite CX3 suitable for night diving?

It can be, as long as you use it within your training limits and carry a tested backup light. Check the manufacturer’s stated beam and burn time specifications to confirm it meets your dive plan.

How often should I replace the O-ring?

Inspect it after every dive and replace it whenever you see cracks, nicks, flattening or debris you cannot clean away. Many divers also replace it on a regular schedule as a precaution.

Should I carry a backup light with the CX3?

Yes, especially on any night, cave or wreck dive. A second independent light is standard practice in most training agencies and protects you if the primary fails.

Conclusion

A Dive Rite CX3 light performs well when it is set up carefully, mounted sensibly and maintained after every dive. Focus on the O-ring, beam angle and a tested backup, and most light-related problems never reach the water. If you dive in conditions beyond your current training, consult a qualified instructor before relying on any light for those dives.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our scuba gear for women guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Scuba Women.