We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Sola Dive Light Repair: Common Faults and What You Can Fix

Sola dive light repair guide: common faults like flickering, dead batteries and water leaks, plus which fixes you can do yourself and when to send it in.

Updated November 2026

Most sola dive light repair jobs come down to three things: a flat or failing battery, a charging problem, or water that got past a seal. Before you assume the light is dead, check the battery and charge state, clean the contacts, and inspect the O-ring. Many faults are fixable at home in under an hour, but anything involving the LED driver or a flooded housing should go to the manufacturer or a qualified repair technician.

Why Sola Dive Lights Stop Working

Dive lights are sealed, so when one fails, the cause is usually electrical or mechanical rather than a single broken part. Owners commonly report these symptoms:

Shopping for one? See our guide: 5 Best Scuba Dive Light Picks: Top Options Compared (2026).

  • Light won’t turn on: usually a depleted or cold battery, a poor battery contact, or a switch that has been pressed while wet.
  • Flickering or dimming mid-dive: often a loose battery connection or a battery that is near the end of its charge cycle life.
  • Charging indicator stays off: a dirty charging contact, a faulty cable, or a charger not seated correctly.
  • Fogging or water inside the lens: a compromised O-ring or a cracked lens seal, which is a safety issue and should be addressed before the next dive.

Factors That Affect Repair Options

Whether a repair is practical depends on what failed and how the light was handled. A light that simply ran out of power is a five-minute fix. A light that flooded, took a hard impact, or was stored with a discharged lithium battery may have damage you cannot see from the outside. Lithium-ion cells that have been over-discharged or physically stressed can be unsafe to charge, so treat any swollen, hot or leaking battery as a hazard and stop using it.

Age matters too. Rechargeable cells lose capacity over hundreds of charge cycles, so a light that runs much shorter than it used to may need a new battery rather than a repair.

How to Troubleshoot and Fix a Sola Dive Light

  1. Rinse the light in fresh water and dry it completely before opening anything.
  2. Fully charge the battery using the supplied charger and cable, then try the light again.
  3. Clean the charging contacts and battery terminals with a dry cloth or a soft brush. Remove any salt or grit.
  4. Inspect the O-ring for nicks, flattening or debris. Clean it, lightly grease it with silicone lubricant made for dive gear, and seat it properly.
  5. Check the switch and housing for cracks. If water has entered, stop, rinse, dry, and contact the manufacturer before powering it on again.
  6. If the light still fails after these steps, the problem is likely the battery or internal electronics. Contact Sola support or an authorized repair service.

Always consult the manufacturer’s manual for disassembly steps. Opening a sealed housing without the right tools or O-ring replacements can void your warranty and compromise waterproofing, so when in doubt, get professional help.

What We’d Use

A spare O-ring kit sized for your light lets you replace a worn seal without guessing at dimensions. View on Amazon

For sealed housings, a small set of plastic tools helps you open and close the light without scratching the body. View on Amazon

FAQ

Can I replace the battery in a Sola dive light myself?

Often yes, if the battery is a user-replaceable pack. Use the exact battery type the manufacturer specifies and dry the housing thoroughly before reassembling.

Why does my Sola light flicker underwater?

A loose battery connection or O-ring that has let moisture reach the contacts is the usual cause. Reseat the battery and inspect the seal before your next dive.

Is it safe to keep using a light that got water inside?

No. Water in the housing can damage electronics and battery contacts, and it can cause a short. Dry it fully, check with the manufacturer, and do not use it until it has been cleared.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our scuba gear for women guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Scuba Women.