Dive Rite HP50 Canister Light System: Setup, Use and Buying Tips
Learn how the Dive Rite HP50 canister light system works, how to set it up, and what to check before a dive. Practical tips for divers from scubawomen.org.
Updated November 2026
The Dive Rite HP50 canister light system is a canister-style dive light built for divers who want a stable, serviceable primary or backup light. This guide explains what the system is, how to set it up and use it safely, and what to look for when deciding whether it fits your diving. Read it before your next purchase or first dive with the light.
What the HP50 Canister Light System Is
A canister light houses its battery and LED head in a sealed tube, usually with a separate switch and a mounting bracket. The HP50 belongs to Dive Rite’s canister family, which is designed to be clipped to a BCD or a stage bottle rather than held in the hand. Because the canister carries most of the weight, the light can be positioned so your hands stay free for reels, gauges and tools. If you are new to this style, the overview in Dive Rite Canister Light: How to Choose and Use One (Step-by-Step) covers the general concepts before you get into the HP50 details.
Shopping for one? See our guide: 6 Best Canister Dive Lights for Cave Diving (2026).
Setting Up the System Before You Dive
Setup is where most avoidable problems start. Work through the following steps at home, not on the boat.
- Confirm the battery is fully charged and that the charger matches the battery type. Note the charge date in your logbook.
- Inspect the O-ring on the canister lid. Remove it, wipe away old grease and hair, check for nicks or flat spots, and re-lubricate with a silicone-based grease.
- Seat the O-ring in its groove and close the canister. Tighten the lid by hand only, then check the seal by sight and feel.
- Attach the mount to your BCD or stage bottle. Make sure the clip or bracket locks fully and sits where the head will not block your inflator or gauges.
- Run a bench test: switch the light on at each setting, confirm the beam, and switch it off. Repeat the test before every dive day.
If your system includes a switch or cable, check that the connector is clean and free of grit before you close everything up. Manufacturers specify regular O-ring replacement, so follow the service interval in the instruction sheet rather than waiting for a visible problem.
Using the HP50 Safely Underwater
Good technique matters as much as good gear. Keep the light aimed where you need it, and avoid sweeping the beam directly into a buddy’s mask, which can cause glare and disorientation. In low visibility, a steady, moderate beam usually works better than the brightest setting, because high output reflects off suspended particles and reduces what you can see.
Plan your light use the same way you plan gas. Know which setting you will start on, when you will switch to a lower setting, and what you will do if the light fails. Practice switching the light on and off by feel, since your hands may be cold or gloved during an emergency.
Maintenance and Troubleshooting
After every dive, rinse the canister in fresh water, dry the exterior, and store the battery off the charger. Check the lens for salt film and scratches. If the light flickers or dims quickly, inspect the battery contacts and charge level before assuming a fault. For bigger faults, such as water intrusion, stop using the light and have it inspected by a qualified service technician. Dive lights are electrical equipment underwater, so if you are unsure about a repair, consult a professional dive shop or the manufacturer.
Recommended Gear
- Silicone O-ring grease: A compatible silicone lubricant keeps the canister seal supple and reduces the risk of leaks during setup. View on Amazon
- Spare O-ring kit: Keeping a matching replacement O-ring on hand lets you swap a worn seal before a trip instead of canceling a dive. View on Amazon
- Rinse tub or bucket: A dedicated freshwater rinse container makes post-dive cleaning of the canister and mount quick and thorough. View on Amazon
Common Mistakes to Avoid
- Tightening the lid with tools, which can crush or pinch the O-ring.
- Skipping the pre-dive bench test and discovering a dead battery at depth.
- Storing the light fully charged and sealed in a hot car, which shortens battery life.
- Using the highest setting in silty water, which reduces visibility.
- Ignoring a slightly loose mount until it shifts during a dive.
FAQ
Is the Dive Rite HP50 suitable as a primary dive light?
It can serve as a primary light for many recreational dives, especially when clipped to a BCD. For cave or technical diving, most instructors recommend a primary and a separate backup light, so confirm your agency’s requirements.
How often should I replace the O-ring?
Follow the service interval in the manufacturer’s instructions, and replace the O-ring sooner if you see cracks, flat spots or debris you cannot clean away.
Can I use the HP50 without a mount?
The canister is designed to be secured to a mount, and using it loose risks dropping it or losing the light during a dive. Always use the supplied or a compatible mount.
Conclusion
The Dive Rite HP50 canister light system rewards a careful setup, a regular O-ring check and a pre-dive test. Treat each of those steps as part of the dive plan, not an optional extra. With those habits in place, the light will be dependable when you need it most.
Related reading
- Dive Rite LED Lux Canister Light: Setup, Use and Buying Tips
- Dive Rite CX3 Light: How to Choose, Mount and Use It Safely
Ready to choose one?
