We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Sola Dive Light Battery Replacement: A Step-by-Step Guide for Divers

Learn how to safely replace a Sola dive light battery, from opening the housing to resealing the O-rings and testing for leaks before your next dive.

Updated November 2026

Replacing the battery in a Sola dive light is a straightforward job if you take it slowly and keep the housing clean and dry. This guide walks you through identifying the correct battery, opening the light, swapping the cell and resealing the housing so it stays watertight. Work on a clean towel in good light, and never skip the leak test at the end.

Before You Start: Confirm the Battery and Gather Tools

Sola lights use rechargeable lithium-ion cells, and the exact size depends on the model. Check the label on the existing battery or the light’s manual for the cell type and voltage before you buy a replacement. Using a cell with the wrong dimensions can prevent the tail cap or battery tray from seating, which can break the seal.

Shopping for one? See our guide: 5 Best Scuba Dive Light Picks: Top Options Compared (2026).

Gather these items before you begin:

  • A replacement battery matching the model’s specified size and chemistry
  • A soft towel or mat to protect the lens and housing
  • Fresh silicone grease approved for underwater housings
  • A lint-free cloth and a small soft brush
  • New O-rings if the old ones are flattened, cracked or nicked

How to Replace the Battery Step by Step

  1. Turn the light off and dry the exterior. Rinse the light in fresh water if it has been used in salt water, then dry it thoroughly. Any water left near the seals can end up inside the housing.
  2. Unscrew the tail cap slowly. Hold the head and body steady and turn the cap counterclockwise. Keep the O-ring with the cap so it does not fall into sand or get lost.
  3. Remove the old battery. Slide the cell out of the tube, noting its orientation. Polarity matters, so check that the positive and negative ends line up with the contacts before you insert the new one.
  4. Insert the new battery. Seat it firmly in the same orientation and confirm the contacts make solid contact with the springs or terminals.
  5. Inspect and clean the O-rings and sealing surfaces. Wipe away old grease and any grit with a lint-free cloth. Check each O-ring for cuts, flat spots or debris, and replace any that look damaged.
  6. Lubricate lightly. Apply a thin film of silicone grease to the O-ring, not the sealing surface itself. Too much grease can attract dust and leave a film that interferes with sealing.
  7. Reassemble and tighten by hand. Thread the cap on carefully so it does not cross-thread, then tighten until the O-ring is seated evenly. Avoid using tools, which can overtighten and crack the housing.

How to Test the Seal and Charge the New Battery

Before you take the light near water, confirm it switches on and check that the seal holds. Turn the light on, then off, and look for any sign of a flicker or water inside the lens. Charge the battery fully using the charger designed for your model, since a mismatched charger can damage the cell. For another angle, check out Genwiss Dive Light Battery Replacement: Step-by-Step Guide (2026).

Run a Simple Leak Check

Submerge the sealed light in a sink or shallow tub of fresh water for a few minutes, watching for bubbles around the cap and lens. Dry the light completely afterward and check the inside of the tail cap for any moisture. If you see water or the light fails to work, open it again and inspect the O-rings.

Common Mistakes to Avoid

  • Reversing the battery, which can damage the electronics or the cell
  • Using petroleum jelly or household grease instead of silicone-based lubricant
  • Reusing a nicked or flattened O-ring because it looks fine at a glance
  • Tightening the cap with pliers or a wrench, which can crack the housing
  • Skipping the leak test and discovering a flood on your next dive

A dedicated silicone grease made for underwater housings helps you lubricate O-rings without leaving residue that attracts grit. View on Amazon

A set of replacement O-rings in the correct size for your light gives you a spare if the originals show wear. View on Amazon

FAQ

Can I use any rechargeable battery in my Sola light?

No. Use a cell that matches the size, chemistry and voltage specified for your model. Mismatched batteries can prevent proper sealing or damage the electronics.

How often should I replace the O-rings?

Inspect them before every dive and replace them when they show cuts, flattening or debris. Many divers swap them on a regular schedule as well, since small wear is hard to judge by eye.

What should I do if my light still leaks after replacing the battery?

Open the housing, clean the sealing surfaces and inspect the O-rings again, replacing any that look damaged. If the problem continues, consult a qualified dive equipment technician before using the light underwater.

Conclusion

Replacing a Sola dive light battery is manageable with a clean workspace, the correct cell and careful O-ring care. Always complete a leak check before diving, since a seal you cannot see is the one that matters most. With a little practice, the job takes only a few minutes.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our scuba gear for women guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Scuba Women.