Light and Motion Sola Dive 1200 Torch: Setup, Beam Use and Buying Tips
Learn how to set up, use and choose a light and motion sola dive 1200 torch, with beam tips, mounting advice and common mistakes to avoid underwater.
Updated November 2026
The light and motion sola dive 1200 torch is a compact, high-output dive light that many divers use as a primary or backup light for night dives and low-visibility conditions. This guide walks you through getting the light ready, using its beam properly and deciding whether it suits the way you dive. By the end, you should know how to mount it, when to use each beam setting and what to check before you buy.
Step 1: Check the Light and Get It Ready
Before any dive, inspect the housing, O-rings and battery compartment. Look for grit or hair on the O-ring and clean it with fresh water. Replace any O-ring that looks flattened, nicked or dry. Manufacturers specify a light O-ring lubricant, and applying a thin, even film helps the seal stay intact.
Shopping for one? See our guide: 4 Best Light and Motion Dive Torch Options for Night Diving.
Charge the battery fully before the dive. If you are unsure how to charge or store the cells, see the step-by-step guide at Sola Dive Light Charging: A Step-by-Step Guide for Divers.
Step 2: Mount the Light Securely
Most divers mount the sola dive 1200 on a handheld grip, a wrist strap or a clamp on the BCD. Choose the position that keeps the beam where you look, not where your hands are. A wrist-mounted setup frees both hands for reels, slates and camera work, but it can drift if the strap is loose. Tug the light firmly before you descend.
If you want to compare mounting styles for your dive, Wrist Mounted Dive Light: 7 Tips for Choosing and Using One Safely covers the trade-offs in more detail.
Step 3: Use the Beam Settings Well
The sola dive 1200 is built around a high-output beam, so pick the setting that matches the task. Use the brightest setting for signaling, locating your buddy and scanning open water. Drop to a lower setting when you are working close to a reef, photographing subjects or conserving battery for a long dive. Lower settings also reduce backscatter, which is the glare from particles in the water that washes out your view.
Think about beam width as well as brightness. A focused beam reaches further but lights a smaller area, while a wider beam covers more of the reef at close range. Wide or Narrow Beam Dive Light: Which Should You Choose? explains which pattern suits which kind of diving.
Step 4: Run a Pre-Dive and Post-Dive Check
- Confirm the power switch and beam selector respond as expected.
- Verify the battery indicator shows adequate charge for the planned dive time, with a margin.
- Check the housing seal before entry and rinse the light in fresh water after the dive.
- Dry the light, open the battery compartment and inspect for moisture or corrosion.
If something fails, the fault is often simple. For common issues and what you can repair yourself, see Sola Dive Light Repair: Common Faults and What You Can Fix.
Buying Tips for the Sola Dive 1200
Before buying, decide how you will use the light. A primary light for technical or cave-adjacent diving needs a longer run time and a reliable backup. A recreational diver using it mainly for night reef dives may prioritize beam quality and mounting flexibility. Compare the sola dive 1200 against its smaller sibling in Light Motion Sola Dive 500: Setup, Beam Use and Buying Tips if you want to see whether the extra output is worth it for your diving.
Common Mistakes
- Running the brightest setting the whole dive, which drains the battery quickly and increases backscatter.
- Skipping the O-ring inspection and lubrication, the most common cause of housing leaks.
- Mounting the light so it points at your hands or the surface instead of the area you are watching.
- Storing the light with a partial charge or in a hot car, which shortens battery life.
- Diving with a single light on a night dive without a backup.
Recommended Gear
- Light and Motion O-ring lubricant: a silicone-based lubricant keeps housing seals supple between dives. View on Amazon
- Wrist strap for dive lights: a secure strap keeps the light in your line of sight and frees your hands. View on Amazon
- Spare O-ring kit for dive lights: carrying spares lets you fix a seal problem on the boat rather than cutting the dive short. View on Amazon
FAQ
Is the light and motion sola dive 1200 suitable for night diving?
Yes, its high-output beam makes it well suited to night reef dives and low-visibility conditions. Pair it with a backup light, as recommended by most dive training agencies.
How often should I service the O-rings?
Inspect them before every dive and replace them when they show nicks, flattening or dryness. Manufacturers specify regular lubrication, so follow their maintenance schedule.
Can I use the light as a backup or signaling light?
Yes, its bright setting works well for signaling your buddy and locating equipment. Keep a separate backup light for emergencies, and consult a dive professional before relying on any single light for technical diving.
Conclusion
With a careful pre-dive check, a secure mount and sensible use of the beam settings, the light and motion sola dive 1200 torch can be a reliable tool for night and low-visibility diving. Maintain the housing seal, manage battery life and always carry a backup. Consult a qualified dive instructor if you are planning technical or overhead dives.
Related reading
Ready to choose one?
