Princeton Tec Amp 10 Dive Light: Setup, Use and Buying Tips
Learn how the princeton tec amp 10 dive light works, how to set it up, use its beam well, and avoid common mistakes before your next dive.
Updated November 2026
The princeton tec amp 10 dive light is a compact, handheld underwater light that many divers use as a primary or backup source. This guide walks you through what to check before you dive, how to set up the light for reliable use, and how to choose the right beam and mounting for your dives. By the end, you will know how to get dependable output and avoid the errors that cause most light problems underwater.
Check the Light Before You Pack It
Most light failures come from preventable issues: a dead battery, a loose cap, or a worn seal. Start with a pre-dive check at home so you are not discovering problems at depth.
Shopping for one? See our guide: Princeton Tec Dive Light Review: Strengths and Limitations.
- Confirm the battery charge or replace the cells if the light has been stored for a long time.
- Inspect the O-ring for nicks, dirt or hair. Clean it, then apply a thin layer of silicone grease.
- Check the lens for scratches or cloudiness that could scatter the beam.
- Turn the light on in a dark room to confirm the output level you expect.
- Pack a spare light or backup light for any dive where you rely on it for navigation.
Manufacturers recommend rinsing the light in fresh water after every dive and keeping the O-ring clean. A small amount of salt crystal in the seal is enough to let water in over time.
Set Up the Light for Your Dive
Before you enter the water, decide how you will carry the light and what output level you need. For a night dive along a reef, a bright, wide beam helps you see the surrounding area and keeps your buddy in view. For a cave or wreck penetration, a narrower, focused beam reaches farther down a passage.
Mount the light so it can be reached quickly without snagging on your gear. Many divers clip it to a D-ring or stow it in a pocket on the BCD. Test the switch with gloves on so you know how it feels when your hands are cold.
Choose a Beam Style
A wide beam lights up more of the environment and works well for general observation. A focused beam gives more distance and is better for spotting animals at range. If you are unsure which to use, start with the wider setting and switch as the dive demands.
Use the Light Safely During the Dive
Keep the light pointed away from your buddy’s eyes, especially at close range. Dimming or switching to a lower output setting helps preserve battery life and reduces glare. Avoid sweeping the beam across the reef, since this can disturb marine life and reduce visibility for others.
Track your remaining battery time and plan to switch to a backup light before the primary runs low. Tell your buddy when you are changing settings so you do not lose each other in the dark.
After the Dive: Rinse and Store
Rinse the light thoroughly with fresh water, paying attention to the switch and cap threads. Dry it completely before you open the battery compartment. Store it with the cap slightly loosened or removed, following the owner’s manual, so the O-ring does not stay compressed for long periods.
Common Mistakes
- Skipping the O-ring check before each dive, which is the most common cause of flooding.
- Storing the light with the battery fully drained or fully charged for months.
- Using a focused beam for close-range work and washing out the scene.
- Forgetting to rinse after saltwater dives, which leaves residue on the switch.
- Relying on a single light for night or cave dives without a backup.
Recommended Gear
- O-ring lubricant: A silicone-based grease keeps the seal supple and reduces wear. View on Amazon
- Dive light lanyard or clip: A secure tether keeps the light attached if you need both hands. View on Amazon
- Replacement O-rings: Keeping a spare seal on hand lets you fix a damaged one before a dive. View on Amazon
FAQ
Is the princeton tec amp 10 dive light suitable for night diving?
Yes, many divers use it for night dives as a primary or secondary light. Always carry a backup light for any dive where you depend on it for navigation.
How often should I service the light?
Check the O-ring and clean the light after every dive, and inspect the seals more thoroughly every few months. Follow the manufacturer’s maintenance schedule in the owner’s manual.
Can I use it in cold water?
Cold water does not usually harm the light, but it can make the switch harder to operate with gloves. Test the controls before the dive and consult your dive professional if you have concerns about equipment in extreme conditions.
Conclusion
A reliable princeton tec amp 10 dive light depends on routine care: checking the O-ring, testing output before each dive, and rinsing after every trip. Set up the beam for your specific dive, carry a backup, and store the light properly between uses. These habits keep your light working when you need it most.
Related reading
- Princeton Tec Shockwave LED Dive Light: 5 Best Picks for Night Diving (2026)
- Princeton Tec LED Dive Light Review: Strengths and Limitations
- Princeton Tec Genesis Dive Light: 5 Best Picks for Night Diving (2026)
Ready to choose one?
