Dive Rite LX20 Handheld Primary Dive Light: Setup, Use and Buying Tips
Learn how to choose, set up and use the Dive Rite LX20 handheld primary dive light safely, with tips on runtime, mounting and pre-dive checks.
Updated November 2026
The Dive Rite LX20 handheld primary dive light is a compact, high-output lamp meant to serve as your main light on night dives, wreck penetrations and low-visibility work. This guide walks you through what to check before you buy, how to set it up for a dive, and how to use it so you can see clearly without wasting battery or blinding your buddy. If you are a woman diver sizing up gear for a smaller hand, these points also help you judge whether a handheld primary is comfortable to hold for a full dive.
Decide Whether a Handheld Primary Fits Your Diving
A handheld primary makes sense when you dive at night, in caves or wrecks, or in murky water where a backup light alone will not cut it. It is also useful if you want to show a buddy or a subject something specific, since you can aim it precisely. If most of your diving is daytime reef work, a smaller backup light may be enough. For a broader comparison, see Dive Rite CX3 Handheld Light: Setup, Use and Buying Tips for Divers and Wide or Narrow Beam Dive Light: Which Should You Choose?
Shopping for one? See our guide: 6 Best Dive Rite Backup Lights for Safe Night and Technical Dives.
Set Up the Light Before Every Dive
Good setup takes about ten minutes and prevents most in-water failures. Work through these steps at home or on the boat, not in the water.
- Inspect the O-ring and lens. Look for hair, grit or nicks. Clean the seal with fresh water and a lint-free cloth, then lightly coat it with silicone grease.
- Charge or check the battery. Confirm the charge indicator and run a quick test on the mode you plan to use first.
- Check the handle and lanyard. Make sure the grip fits your hand comfortably and that the wrist strap is secure and not frayed.
- Seat the cap, then press the switch. Leak-test by tightening the cap to the manufacturer’s stated torque, and confirm the light still works.
- Pack a backup. Carry a separate backup light and a spare battery or charged source, even on short dives.
Use the Light Efficiently Underwater
Most divers run their primary light too bright and too long. Start on a lower output setting for general navigation and step up only when you need to read a gauge, inspect a feature or signal. Keep the beam angled slightly down or to the side rather than straight into your buddy’s eyes or into particulate, which causes backscatter.
Hold the light in the hand that is not your main reference hand, so you can keep a steady grip on a line or rock. When you need both hands, clip the light to a D-ring or a secure point on your harness rather than letting it dangle. Check your runtime at the start of each dive and note how fast the battery drops on your chosen setting, since manufacturers’ runtime figures assume specific conditions.
Plan Your Dive Around Light Limits
Decide your turn-around point based on how much light you have, not how much you want. Track elapsed time and battery level together. If the light drops to a low-charge mode, begin your ascent or switch to your backup light, and agree on a simple light signal with your buddy so you both know when a light is failing. Consult a qualified instructor if you are unsure how light limits affect your dive plan, especially for penetration or cave diving.
Common Mistakes to Avoid
- Skipping the O-ring check, which is the most common cause of flooding.
- Running the light on full output for the whole dive.
- Pointing the beam directly at your buddy’s face or into silt.
- Relying on a single light for a night or penetration dive.
- Storing the light with the battery fully drained or fully charged for long periods.
Recommended Gear
- Silicone grease for O-rings: keeps the light’s seals supple and reduces the chance of leaks. View on Amazon
- Dive light lanyard or wrist strap: keeps the light secure in your hand and prevents loss during a current or a tumble. View on Amazon
- Backup dive light: a second, independent light gives you a safe exit if the primary fails. View on Amazon
FAQ
Is the Dive Rite LX20 suitable for daytime diving?
It can be, but most divers use a handheld primary mainly after dark or in low visibility. For daytime reef dives, a smaller light used at low output is usually more practical.
How often should I check the O-rings?
Inspect them before every dive, and clean and re-grease them after each day of diving or any time you see debris. Replace any O-ring that shows cracks, flattening or nicks.
Do I still need a backup light if I have a primary?
Yes. A separate backup light is standard practice for night and technical diving, because it gives you a light source that does not depend on the primary working.
Conclusion
The Dive Rite LX20 handheld primary dive light performs best when you set it up carefully, run it at the output you actually need, and plan your dive around its runtime. Check the seals, carry a backup, and agree on light signals with your buddy. Those habits will do more for your safety than any single feature on the light.
Related reading
- Dive Rite LED Lux Canister Light: Setup, Use and Buying Tips
- Dive Rite Canister Light: How to Choose and Use One (Step-by-Step)
- Dive Rite CX3 Light: How to Choose, Mount and Use It Safely
Ready to choose one?
